More Details

 

This article listed below involving How to Install a Bathtub is exceedingly attention-grabbing. You should investigate it.

Setting up a tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently accessible, the task can move quickly; if you have to open up a wall surface to get rid of the old bathtub and also position the new tub, the task is much harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make sure you have certified on your own for the job and are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to think about employing one before you start. Chances are you may need a specialist plumber to make tube connections.
This article will certainly help you install a new bathtub in your shower room if you have actually already acquired a brand-new tub as well as don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and product list should make up the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the restricted access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the tap and also the sink. Protect the faucet in position with the manufacturer supplied backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind should be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Installing the Tub

Using the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to make sure that the tub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the tub until the level checks out degree.
To mount taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water as well as check all joints and also new pipework for leakages as well as tighten them if essential. Fill the bath tub and likewise examine the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and securing around the bathtub needs to wait till the tub has been used at least once as this will resolve it right into its final placement.

 

 

Preparing for the Installation

Firstly, the sustaining structure supplied with the bath ought to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final position.

 

 

Tiling Around the Bath tub

In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the bathtub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently available on the market. It is advisable to fit the floor tiles using water-resistant or waterproof glue as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I'm very drawn to Installing A Bathtub and I hope you enjoyed the new blog posting. Sharing is good. One never knows, you will be doing someone a favor. I enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.

Protect plumbing integrity; connect now.